Описание
 | |||
 |  |  |  |
 |  |  |  |
 |  |  |  |
Notice:
We only supply genuine Leadshine servo motor drive with reasonable price, if your budget is limit, please contact our service man online and he she will recommend you the low price other supplier.
DM2282 2-Phase 32-Bit DSP Digital Stepper Drive
(3 pieces per lot)
The DM2282 stepper drive adopts advanced features like electrical damping, anti-resonance, start-up smoothing, multi-stepping... With the input voltage of 90 - 230 VAC / 115 - 325 VDC and output current of 0.50 - 8.20 A, it is capable of driving a wide range of 2-phase stepper motors with high precision at extra smoothness, quietness, and very low motor heating.
Its multi-Stepping feature allows a low resolution step input to produce a much higher microstep output for smoother & quiet motor movement, and much lower motor heating. This feature will significantly improve the performance of your stepper control systems.
A DM2282 stepper drive is easy to setup and configure via DIP switches. There are 15 resolution settings from 400 - 25600, and 7 output current settings from 0.50 - 8.20. Also, a user can simply set the idle current to full (100%) or 50% of the output current via a DIP switch.
Features:
Step & direction or CW/CCW control
DSP-based stepper control technology
Anti resonance
Automatic motor identification and self configuration
Extra low noise
Extra smooth movement
Low drive & motor heating
Maximum frequency: 200KHz
Input voltage: 90 - 230 VAC / 115 - 325 VDC
Output current: 7 selections of 0.50 - 8.20A via DIP switches; or any value of 0.1-8.20A via software configuration
Micro steps: 15 selections of half - 128 step via DIP switches; or full - 512 step via software configuration
Automatic idle current reduction
Specification
Model:DM2282
Phase:2
Control Mode:Step & Direction
Max Input Frequency:200KHz
Input Voltage Range:90 - 230 VAC /
115 - 325 VDC
Output Current:0.50 - 8.20 A
Software Cofig. Resolution Range:200 - 102,400 (increased by 200)
# of DIP Switch Resolution Configurations:15
DIP Switch Resolution Setings:400, 800, 1600, 3200, 6400, 12800, 25600, 1000, 2000, 4000, 5000, 8000, 10000, 20000, 25000
Software Cofig Current Range:0.50 - 8.20A (increase by 0.1A)
# of DIP Switch Current Configurations:7
DIP Switch Current Configurations:2.2A, 3.2A, 4.2A, 5.3A, 6.2A, 7.2A, 8.2A
Logic Current Range:7-16mA (10mA typical)
Logic Voltage Range:4-5 VDC for pulse active high (default) , or 0-0.5V for pulse active low
Communication Type:RS232
Pulse enabled at:Rising edge
Idle Current Percentage:50 %
Software Config. Idle Current Percentage:0-100%
# of Digital Inputs:3
# of Digital Onputs:1
Step Width:2,500 ns
Minimal Direction Setup Time:5,000 ns
Protection:Over-current, over-voltage, under-voltage, phase-error, and over-temperature protection
Isolation Resistance:500M Ohm
Environment:Avoid dust, oil fog and corrosive gases
Ambient Temporature:0-50°C
Humidity:40–95% RH
Operating Temporature:0-70°C
Vibration:5.9 m/s2 Max
Storage Temporature:-20-65°C
Specification:7.87 X 5.39 X 3.19 Inches
Weight:2.86 lbs
Electrical Specifications
Connector
Microstep Resolution Selection And Current Setting
Typical Connection
Mechanical Specification
Companion products
86HS35 (stepper motor)
HS3442 (Stepper Motor)
HS3468 (Stepper Motor)
HS3485 (Stepper Motor)
HS34100 (Stepper Motor)
HS4212 (Stepper Motor)
HS4215 (Stepper Motor)
HS4220 (Stepper Motor)
Real Photo:
| |||
|  |  |  |
 |  |  |  |
 |  |  |  |
Характеристики
- Тип двигателя
- Шаговый электродвигатель
- Номер модели
- DM2282
- Питание
- Переменный ток
- Control Mode
- Step & Direction
- Max Input Frequency
- 200Khz
- Input Voltage Range
- 90 - 230 VAC / 115 - 325 VDC
- Output Current
- 0.50 - 8.20 A
- Logic Current Range
- 7-16mA (10mA typical)
- Logic Voltage Range
- 4-5 VDC for pulse active high (default)
- Communication Type
- RS232
- Step Width
- 2,500 ns
- Isolation Resistance
- 500M Ohm
- Protection
- Over-current, over-voltage, and stall
Сопутствующие товары
